1 ... 20 21 22 23 24 25 26 27 ... 36

Operating Instructions General Settings Guide - səhifə 24

səhifə24/36
tarix08.10.2017
ölçüsü5.73 Kb.

Troubleshooting
74

4


Cannot print in duplex 
mode.
You cannot use paper in 
the bypass tray for duplex 
printing.
For duplex printing, select Tray 1-2 
in copier mode or with the printer 
driver.

[


Off


]


 is selected for 

[


Duplex


]


 
in Paper Type: Tray 1-2.
Select 

[


On


]


 for 

[


Duplex


]


 in Paper 
Type: Tray 1-2. See p.30 “Paper 
Type:Tray 1– 2”.
You forgot your key opera-
tor code.

Contact your service representative.

Problem


Causes


Solutions



x Clearing Misfeeds
75

4


x Clearing Misfeeds
R

 


CAUTION:


Important


When clearing misfeeds, do not turn off the power switch. If you do, your
copy settings are cleared.
To prevent misfeeds, do not leave any torn scraps of paper inside the ma-
chine.
If paper misfeeds occur repeatedly, contact your service representative.

Note


More than one misfeed area may be indicated. If this is the case, check every
applicable area. Refer to the following charts: A, P, Y.
You can find a sticker explaining how to remove misfed paper inside the right
cover.
When the machine instructs you to reset originals, reset them in the feeding
position. The display will show you the number of originals to return.
• The fusing section of this machine might be very hot. Caution should be tak-
en when removing misfed paper.
ZFOH210E.eps

Troubleshooting
76

4


displayed
displayed
displayed
ABU040S
ABU040S.eps

Changing the Paper Size
77

4


Changing the Paper Size

Preparation


Be sure to select the paper size
with User Tools. If you do not, mis-
feeds might occur. See p.29 “Tray
Paper Size:Tray 1–2”.

Reference


For details about paper sizes and
types, see p.94 “Copy Paper”.

Changing the Paper Size of the 


Paper Tray (Tray 1)


A

Make sure the paper tray is not in


use.


B

Pull the paper tray out slowly un-


til it stops.


Note


Remove any remaining copy
paper.
C

While pressing the release lever,


pull the back fence off from the


tray.


When loading A4
L
 size paper

 Place the back fence in the cor-


ner pocket on the left.


D

While pressing the release lever,


adjust the side fences.


E

Push the metal plate down.


ABU044S
ABU044S.eps
ZFOY640E.EPS
ABU048S
ABU048S.eps
ZFOY340E.eps

Troubleshooting
78

4


F

Square the paper and load it in


the tray.


Important


Be sure to load the paper under
the roller.
Do not stack paper over the lim-
it mark.
G

While pressing the release lever,


adjust the side fences to the new


paper size.


Important


When setting small quantities of
copy paper, be careful not to
squeeze in the side fences too
much or paper will not feed in
properly.
H

While pressing the release lever,


set the back fence to the new size.


I

Push the paper tray in until it


stops.


Changing the Paper Size in the 


Paper Tray Unit (Tray 2)


A

Make sure the paper tray is not in


use.


B

Pull out the paper tray until it


stops.


Note


Remove any remaining copy
paper.
C

While pinching the release lever,


adjust the back fence.


ABU049S
ABU049S.eps
ABU045S
ABU045S.eps
ABU046S
ABU046S.eps
ZFOY370E.eps

Changing the Paper Size
79

4


When loading 8
1
/
4

×
 14"
L
 or 
8
1
/
2

×
 14"
L
 size paper

Pull the back fence off from


the tray.


 Place it in the corner pocket on


the left.


D

While pressing the release lever,


adjust the side fences.


E

Push the metal plate down, and


then square the paper and load it


in the tray.


Important


Do not stack paper over the lim-
it mark.
Load paper so that the paper
touches the right side of the
tray, or misfeeds might occur.
F

While pinching the release lever,


adjust the side and back fences to


the new paper size.


Important


When loading small quantities
of copy paper, be careful not to
squeeze in the side fence too
much or paper will not feed in
properly.
G

Push the paper tray in until it


stops.


ZFOY650E.EPS
ZFOY380E.eps
ZFOY390E.eps
ZFOY400E.eps

Troubleshooting
80

4


Selecting the Paper Size with 


User Tools


A

Press the 

{

User Tools/Counter

}

 key.


B

Select 


[


System Settings


]


 using 

{U}

or 

{T}

, and then press the 

{

OK

}

key.


C

Select 


[


Tray Paper Settings


]


 using


{U}

 or 

{T}

, and then press the


{

OK

}

 key.


D

Select the paper tray you want to


change the paper size for using


{U}

 or 

{T}

, and then press the


{

OK

}

 key.


E

Select the paper size using the


scroll keys, and then press the


{

OK

}

 key.


The “
Programmed
” message ap-
pears.
F

Press the 

{

User Tools/Counter

}

 key.


ABU105S
ABU105S.eps
***ZEN073.tif***
***ZEN074.tif***
***ZEN075.tif***
***ZEN083.tif***


Dostları ilə paylaş:

©2018 Учебные документы
Рады что Вы стали частью нашего образовательного сообщества.
?


opredelenie--odno-ili-2.html

opredelenie--principi.html

opredelenie-3.html

opredelenie-8.html

opredelenie-aktivnosti.html